Acer AR360 F1 Series Скачать руководство пользователя страница 122

Страница: 122 / 188

4 System BIOS

106

Remote Access Configuration

Remote Access: This allows you to enable Remote Access support. If
Remote Access is set to Enabled, the following items will be displayed:

Serial Port Number: This feature allows the user to decide which serial
port to be used for Console Redirection. The options are COM 1 and
COM2.

Base Address, IRQ: This item displays the base address and IRQ of the
serial port used for Console Redirection.

Serial Port Mode: Allows you to set the serial port mode for Console
Redirection.

Flow Control: Allows you to set the flow control for Console
Redirection.

Redirection After BIOS POST: Select Disabled to turn off Console
Redirection after POST or Always to keep Console Redirection active all
the time after POST. Select Boot Loader to keep Console Redirection
active during POST and Boot Loader.

Caution: Some settings may not be supported by some operating
systems.

Terminal Type: Allows you to select the target terminal type for
Console Redirection.

VT-UTF8 Combo Key Support: Select Enabled to enable VT-UTF8
Combination Key support for ANSI/VT100 terminals.

Содержание AR360 F1 Series




























































































































































































Результаты поиска

Содержание AR360 F1 Series

Отзывы:

Похожие инструкции для AR360 F1 Series

Бренды по названию

Популярные бренды

Acer AR360 F1 Series, Руководство пользователя

Результаты поиска

Содержание AR360 F1 Series

Отзывы:

Похожие инструкции для AR360 F1 Series

Бренды по названию

Популярные бренды