Acer Altos G530 Series Скачать руководство пользователя страница 100

Страница: 100 / 190

4 BIOS setup

Fourth IDE
Master

Specifies the current configuration of
the IDE device connected to the master
port of the fourth IDE channel.

Press

Enter

to access the Fourth Master

submenu.

Hard Disk Write
Protect

Enables or disables write protection to
system hard drives.

Disabled

Enabled

IDE Detect Time
Out (Sec)

Select the time out value for detecting
ATA/ATAPI devices.

Used with older IDE devices with longer
spin up times.

ATA(PI) 80-pin
Cable
Detection

Select the mechanism for detecting 80-
pin ATA(PI) cable.

Host &
Device

Host

Device

Parameter

Description

Option

Содержание Altos G530 Series































































































































































































Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды

Acer Altos G530 Series, Руководство пользователя

Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды