Acer Altos G530 Series Скачать руководство пользователя страница 116

Страница: 116 / 190

4 BIOS setup

106

Boot Device Priority

The Boot

Device Priority submenu lets you specify the boot search

sequence during the POST process.

BIOS setup will display an error message if the drive(s) specified is not
bootable.

Parameter

Description

1st Boot Device

Sets the device from which the system will first
attempt to boot up.

Press

Enter

to access the Removable Drives submenu.

2nd Boot Device

Sets the device from which the system will attempt to
boot up when the first attempt failed.

Press

Enter

to access the CD/DVD Drives submenu.

3rd Boot Device

Sets the device from which the system will attempt to
boot up when the first and second attempts failed.

Press

Enter

to access the Hard Disk Drives submenu.

Содержание Altos G530 Series































































































































































































Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды

Acer Altos G530 Series, Руководство пользователя

Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды