Acer Altos G530 Series Скачать руководство пользователя страница 107

Страница: 107 / 190

USB Configuration

The USB Configuration submenu lets you specify settings for USB
devices.

Parameter

Description

Option

USB Function

Enables or disables the UBS host
controller.

When set to Disabled, other USB
options will be grayed out.

Enabled

Disabled

Legacy USB
Support

Enables or disables the support for
legacy USB devices.

When set to Auto, the system detects
the presence of USB devices at startup.

If a USB device is detected, the USB
controller legacy mode will be enabled.

Auto

Disabled

Keyboard only

Keyboard and
Mouse

Port 60/64
Emulation

Enables the I/O port 60/64h emulation
support.

This parameter is enabled by default
and is not user-configurable.

Enabled

Содержание Altos G530 Series































































































































































































Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды

Acer Altos G530 Series, Руководство пользователя

Результаты поиска

Содержание Altos G530 Series

Отзывы:

Похожие инструкции для Altos G530 Series

Бренды по названию

Популярные бренды