47
43
Unit of measure
Dat
a
Adjustment range
Default
UNIT
°C .. °C
°C
ATTENTION
The variation of the unit of measure from ° C to ° F or vice versa,
will result in the restoration of the "default" data, or the loss of
all personal data contained and stored in the control unit, such
as thermal parameters, hydraulic diagram, meters , password
and anything else stored in the internal memory of the control
unit itself.
Restoring the default data could be exploited, for example, if the
installer wanted to reset the factory data without, however,
manipulating all the parameters individually.
If the unit of measurement is changed, the control unit will be
reset to diagram n.1 and will show on the display for about 6
seconds, the writing 'RST data', indicating that all data has been
restored to default values.
P12: MINIMUM MANIFOLD TEMPERATURE LIMITATION
The 'Minimum Temperature Limitation' parameter of the collector is
used for the management of the Minimum Thermostat relating to the
activation of the collector pumps.
This thermostat prevents the manifold pumps from being activated if
a temperature lower than that set in the parameter is detected on the
relevant panel.
The 'Minimum Temperature Limitation' function will not be active in
ABC operation or if the manifold pumps are activated due to the
Recooling function or other functions.
SELE
CT
PARAMET
E
R P11
PRE
SS
KEY
‘
8
’
THROUGH THE ARROWS
‘
’ o
r
‘
’
IT IS POSSIBLE TO
CYCLICALLY SCROLL BETWEEN THE FOLLOWING
REGULATION THERMAL DATA:
- 'MTC' minimum collector temperature setting -
Enabling / disabling limitation
min.
temperatur
e
‘MTEN’
PRE
SS KEY
‘
8
’
TO ENTER IN MODIFICATION OF THE
SELECTED THERMAL DATA;
THE DATA STARTS TO FLASH
THROUGH THE ARROWS
‘
’ o
r
‘
’
SET THE NUMERICAL VALUE
PRE
SS KEY
‘
8
’
TO CONFIRM THE SETTING MADE
OR PRESS THE 'esc' KEY TO CANCEL THE CHANGE
Minimum collector temperature setting
Dat
a
Adjustment range
Default
MTC
10.0 °C .. 90.0 °C
10.0
°C
Enable / Disable min. Temperature limitation
Dat
a
Adjustment range
Default
MTEN
0 .. 1
0
Note: with '0' the minimum collector temperature limitation
function is deactivated, while with '1' it is activated.
P14: COLLECTOR RESET TEMPERATURE
With this parameter it is possible to set the temperature value ('T_SE'
- 'T_SW') for resetting the collector pump if the TS_2 safety
temperature has intervened, in order to avoid thermal shocks and air
pockets in the system. .
The collector pump will be automatically restarted only if the collector
temperature, detected by the sensor S_1 for the EAST collector or
S_4 for the WEST collector, is lower than the reset temperature of
the collector, respectively, T_SE or T_SW.
SELE
CT
PARAMET
E
R P14
PRE
SS
KEY
‘
8
’
THROUGH THE ARROWS
‘
’ o
r
‘
’
IS POSSIBLE TO SCROLL
CYCLICALLY BETWEEN THE FOLLOW ADJUSTMENT DATA
:
-
Collector reset temperature
EST
‘T_SE’
-
Collector reset temperature
OVEST
‘T_SW’
PRE
SS KEY
‘
8
’
TO ENTER IN MODIFICATION OF THE
SELECTED DATA;
THE DATA STARTS TO FLASH
PRE
SS KEY
‘
8
’
TO CONFIRM THE SETTING MADE
OR PRESS THE 'esc' KEY TO CANCEL THE CHANGE
Collector reset temperature
EST
Dat
a
Adjustment range
Default
T_SE
OFF / 60 °C .. 180 °C
OFF
Note: 1: The 'T_SW' parameter is visible only if a hydraulic
scheme with two manifolds has been selected
EST / OVEST.
FUNCTIONS ACCESSIBLE TO THE USER
The functions accessible by the user are limited and do not
allow you to configure the data that affect the management of
the system. The only operations allowed to the user are the
following: - Switching on / off the control unit
- Activation / Deactivation ABC function of the control unit.
Menu
SELE
CT KEY
‘
’
TO ACCESS THE
'USER PARAMETERS'
THE FIRST 'USER PARAMETER'
IS DISPLAYED
THROUGH THE ARROWS
‘
’ o
r
‘
’
IT IS POSSIBLE TO
SCROLL CYCLICALLY THROUGH THE USER
PARAMETERS
- 'MTC' minimum collector temperature setting -
Enabling / disabling limitation
temperatur
e min.
‘MTEN’
THROUGH THE ARROWS
‘
’ o
r
‘
’
IT IS POSSIBLE TO
CYCLICALLY SCROLL BETWEEN USER PARAMETERS:
U1: MAXIMUM TEMPERATURE DISPLAY U2:
ANTIFREEZE ACTIVATION / DEACTIVATION
PRE
SS KEY
‘
8
’
TO ENTER THE SELECTED
PARAMETER
44
SET THE DATA RELATING TO EACH SINGLE
PARAMETER AS SHOWN BELOW
PRESS THE 'esc' KEY TO RETURN TO THE USER
PARAMETERS SECTION
WAIT 20 SECONDS OR PRESS THE 'esc' KEY TO EXIT
USER MODE.
WARNING!
In 'USER PARAMETERS' mode, all outputs are disabled.
Display of Maximum Recorded Temperatures
The 'TMAX U1' parameter allows you to view the maximum
temperature recorded in the system by each TM- probe.
PRE
SS KEY
‘
8
’
TO ACCESS THE
TEMPERATURE DISPLAY
THROUGH THE ARROWS
‘
’ o
r
‘
’
IT IS POSSIBLE TO
SLIDE CYCLICALLY BETWEEN THE DETECTED
TEMPERATURES:
TM1
TM2
TM3
TM4
PRE
SS KEY
‘
8
’ I
THE DISPLAY SHOWS THE NUMBER
OF THE FLASHING PROBE
INSTEAD, PRESSING THE 'esc' KEY RETURNS TO THE
DISPLAY OF USER PARAMETERS
PRE
SS KEY
‘
8
’
THE TEMPERATURE RECORDED SO
FAR IS RESET; PRESSING INSTEAD
'Esc' YOU RETURN TO THE DISPLAY OF THE STORED
TEMPERATURE
PRESS THE 'esc' KEY TO EXIT THE MAXIMUM
TEMPERATURE DISPLAY
Activation of the Antifreeze
The 'AFR U2' (anti frost) parameter allows you to activate or
deactivate the antifreeze function.
The management of the antifreeze data is done through the user
parameters.
PRE
SS KEY
‘
8
’
THE DISPLAY SHOWS FLASHING 'AFR'
THROUGH THE ARROWS
‘
’ o
r
‘
’
IT IS POSSIBLE TO
ACTIVATE OR DEACTIVATE THE ANTIFREEZE:
0: OFF
1: ACTIVE (THE DISPLAY SHOWS
❄
)
PRE
SS KEY
‘
8
’
TO CONFIRM THE SETTING OR
PRESS THE 'esc' KEY TO EXIT USER PARAMETERS
WARRANTY
With a view to continuous development of its products, the manufacturer reserves the right to make changes to technical data and performance without prior
notice.
The consumer is guaranteed against conformity defects of the product according to the European Directive 1999/44 / c as well as the document on the policy of
manufacturer's warranty.The full text of the guarantee is available from the seller on request.
MANAGEMENT OF ANOMALIES AND POSSIBLE CAUSES
60
GESTIONE ANOMALIE E PROBABILI CAUSE
ANOMALY
POSSIBLE CAUSE
During normal operation, the control
unit shows the symbol on the display
and emits an acoustic signal
characterized by a series of 'beeps'.
The probe that generated the
problem flashes.
The control unit has detected an anomaly on the probes.
The number of the faulty probe will be displayed and the type of anomaly present will be
indicated.
The display shows the icon
and
the control unit emits an acoustic
signal characterized by a series of
'beeps'.
One or more probes have detected a temperature higher than the relative safety
temperature set.
In selecting the system to be
built (installer parameter
P1)
one or more probes flash.
The probe has not been connected or is faulty.
Probe in short circuit
(R≈0).
COL ShrT
S_2 ShrT
S_3 ShrT
S_4 ShrT
Open probe
(R=∞).
COL OPEn
S_2 OPEn
S_3 OPEn
S_4 OPEn
GARANZIA
Nell’ottica di un continuo sviluppo dei propri prodotti, il costruttore si riserva il diritto di apportare modifiche a dati tecnici e
prestazioni senza preavviso. Il consumatore è garantito contro i difetti di conformità del prodotto secondo la Direttiva Europea
1999/44/
c
nonché il documento sulla politica di garanzia del costruttore. Su richiesta è disponibile presso il venditore il testo
completo della garanzia.
WARRANTY
With a view to continuous development of its products, the manufacturer reserves the right to make changes to technical data and performance
without prior notice. The consumer is guaranteed against conformity defects of the product according to the European Directive 1999/44
/ c as well as the document on the policy of manufacturer’s warranty.The full text of the guarantee is available from the seller on request.
