background image

3 Product Description

Hazards 

caused by improper use

If improperly used, the device can present risks to persons, animals, and material 

property. 

WARNING

Use the device according to its designated use only.

Do not convert and modify the device to enhance its performance without

authorization.

Only qualified personnel are permitted to perform work on the device or

system.

3 Product Description

3.1 Technical Data

Ambient temperature of welding

-

1

0

 

°C to + 40

 

°C

Relative humidity

Up

 to 90

 

% at 20

 

°C

Tab. 1

Ambient conditions during operation 

Storage in a closed enviornment, ambient temperature
Ambient Temperature for shipment
Relative Humidity

Up

 to 90% at 20°C

Tab. 2

Ambient conditions for transport and storage 

-

1

0

 

°C to + 40

 

°C

-

25

 

°C to + 

55

 

°C

Type of voltage

DC

Polarity of the electrodes

Usually positive

Wire types

C

ommercially available round wires

Type of use

A

utomatic

Voltage rating

Peak value of 141 V

Protection type of the machine-side connections 

IP3X (EN 60 529)

Shielding gas (

EN ISO 14175)

CO

and mixed gas M21

Tab. 

3

Generial torch data according to EN 60 974-7

EN 

6

 

xFUME

®

ABIROB

®

A

F500

Содержание xFUME ABIROB AF500






















Отзывы: