Abicor Binzel ALPHA 1 Скачать руководство пользователя страница 4

Страница: 4 / 24

If installing a neckliner into a new swanneck or swanneck without old

neckliner for measuring length:

1. Fit the consumables (diffuser/insulator, tip-holder, contact tip, nozzle) onto the swan-

neck.

2. Insert the neckliner into the swanneck as far as it will go.

3. Measure the length of liner sticking out from the back of the swanneck and subtract

1 mm. (When cut and installed correctly, the neckliner should stick out approximately

1 mm. without tension.)

4. Remove the liner and measure the length from step 3 back from the inserted end and

mark carefully. With a pair of sharp cutters, cut off the excess liner.

5. Check to ensure that there are no burrs or obstructions to the inner

diameter of the liner.

6. Insert the liner into the swanneck, fit the swanneck on the gun body in the desired

position and tighten the swanneck locking ring.

If replacing an existing neckliner:

1. Unscrew the swanneck, remove the old neckliner and measure its length.

2. Carefully cut the new neckliner to the same length as the old liner with a pair of sharp

cutters.

3. Check to ensure that there are no burrs or obstructions to the inner diameter of

the liner.

4. Insert the cut liner into the

swanneck. When cut and

installed correctly, the neck-

liner should stick out

approximately 1 mm

without being held in.

6. Replace the swanneck

on the gun body in the

preferred position and

tighten the swanneck

locking ring.

Installation of neckliners in slip-on

and threaded nozzle swannecks

Liner collet stick-out:

1 mm

Содержание ALPHA 1

























Результаты поиска

Содержание ALPHA 1

Отзывы:

Похожие инструкции для ALPHA 1

Бренды по названию

Популярные бренды

Abicor Binzel ALPHA 1, Инструкция по эксплуатации

Результаты поиска

Содержание ALPHA 1

Отзывы:

Похожие инструкции для ALPHA 1

Бренды по названию

Популярные бренды