Abicor Binzel ALPHA 1 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

8

Allen key

Direct Plug

Torch Rear End

Connector Kit

Internal Gas

Connector plug

Set screw

1. Thread the connector plug into the rear of the torch (the connector plug may differ

from the one shown).

2. Tighten down the set screw with the Allen key provided.

3. Connect the appropriate end of the trigger lead jumper supplied in the kit to the con-

nector exiting the torch (the trigger lead may also differ from the one shown).

4. Install the gun liner supplied with the torch as per the liner installation instructions on

pages 4-5.

5. The torch is now ready to install into the feeder. Finally, hook up the trigger connector

on the feeder side.

Trigger lead jumper

Assembly instructions for direct plug

connector kits: internal gas

«
...
6
7
8
9
10
...
»

Содержание ALPHA 1

























Отзывы:

Нет отзывов

Похожие инструкции для ALPHA 1

Бренд: Veris Industries Страницы: 2

CRD 2 00-1000S Series

Бренд: Symbol Страницы: 16

Бренд: Daga Страницы: 28

Бренд: Samsung Страницы: 15

Бренд: Metra Electronics Страницы: 14

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Speedglas 9100-Air

Бренд: 3M Страницы: 63

Бренд: 3M Страницы: 84

Бренд: RayTek Страницы: 2

Бренд: Ace Bayou Страницы: 8

Бренд: Dacor Страницы: 4

Бренд: IDS Страницы: 22

Бренд: ICON ProAudio Страницы: 29

Бренд: OFFCARR Страницы: 12

Бренд: OEM Tools Страницы: 4

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды