Abicor Binzel ALPHA 1 Скачать руководство пользователя страница 20

Страница: 20 / 24

TROUBLESHOOTING: GENERAL GUIDE

Possible Solutions

Inspect ground cable for loose connections, fraying and cuts. Cor-

rect any problem areas found. Clean clamping area to insure good

contact. Securely attach the ground cable to the workpiece, as close as

possible to the point of welding. Make sure there is a good connection

to the welding power source.

Check to make sure the power connection on the power source is

tight, the connection on the wire feeder is tight, the connection to the

adaptor block is tight, and the connection of the gun to the adaptor

block is tight.

Remove handle assembly and adaptor support. Check to insure the

Bikox connection to the swanneck is tight and the Bikox connection to

the adaptor block is tight.

Visually inspect the Bikox assembly for cuts and tears. Replace the

Bikox assembly if necessary.

Remove nozzle from gun and inspect contact tip and tip holder/gas

diffuser for wear and tightness; replace or tighten as necessary.

Note complete weld parameters, including welding current (Amps),

welding voltage, wire feed speed, type and size of wire, type of gas

and fIow rate of gas and consult your local Authorized ABICOR Binzel

a distributor.

Remove swanneck and inspect interface for dirt build-up. Periodic

cleaning is necessary.

Problems/Causes

AIR-COOLED GUN

RUNNING TOO HOT

Poor ground.

Loose power connection.

Loose Bikox connection.

Damaged Bikox assembly.

Consumable items loose

or worn.

Capacity of gun being

exceeded.

Dirty connection

Approximate x and y measurements are in millimeters and are taken from the end of the contact tip with spray arc set-up.

A1-22

A1-45

A1-60

SWANNECK DIMENSIONS: ALPHA 1 SLIP-ON

Содержание ALPHA 1

























Результаты поиска

Содержание ALPHA 1

Отзывы:

Похожие инструкции для ALPHA 1

Бренды по названию

Популярные бренды

Abicor Binzel ALPHA 1, Инструкция по эксплуатации

Результаты поиска

Содержание ALPHA 1

Отзывы:

Похожие инструкции для ALPHA 1

Бренды по названию

Популярные бренды