Abicor Binzel ALPHA 1 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

9

Assembly instructions for direct plug

connector kits: external gas (Lincoln std. shown)

1. Slide the insulating sleeve over the connector plug (wide end facing the torch) and

screw the plug into the torch rear end.

2. Tighten down the set screw with the Allen key provided.

3. Remove the gas seal and save for possible future use (e.g. for converting the torch to

internal gas). Install the gas nipple in place of the gas seal (removable sealant can be

applied to the threads if so desired, but use care to avoid sealant getting inside the

block).

4. Slide the gas hose over the gas nipple and clamp with the clamps supplied.

5. Connect the appropriate end of the trigger lead jumper supplied in the kit to the con-

nector from the torch rear end.

6. Install the liner supplied with the torch as per installation instructions on pages 4-5.

7. The torch is now ready to install into the feeder. Finally, hook up the gas and trigger

connectors on the feeder side.

Gas seal

Gas

nipple

Set screw

Insulating

sleeve

Connector plug

Allen key

Connector Kit

Lincoln

Standard

Direct Plug

Torch Rear End

Trigger lead jumper

Gas hose

«
...
7
8
9
10
11
...
»

Содержание ALPHA 1

























Отзывы:

Нет отзывов

Похожие инструкции для ALPHA 1

DeltaSphere-3000

Бренд: 3rdTech Страницы: 9

Watchdog Super Elite

Бренд: 4B Страницы: 76

mamaRoo 4M-005-00

Бренд: 4 Moms Страницы: 17

Бренд: Raven Страницы: 70

Бренд: Unimig Страницы: 16

Бренд: Yolink Страницы: 27

Бренд: Antec Страницы: 5

Бренд: PCB Piezotronics Страницы: 15

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Woody Valley Страницы: 15

Бренд: Aptina Страницы: 147

MultiConnect Conduit Series

Бренд: Multitech Страницы: 2

Бренд: Sensit Страницы: 4

Бренд: Whispbar Страницы: 14

Бренд: Manhattan Страницы: 2

Бренд: Kensington Страницы: 4

Бренд: Wetekom Страницы: 19

Centronic VarioControl VC280

Бренд: Becker Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды