manualshive.com logo in svg

Abicor Binzel ALPHA 1, Инструкция по эксплуатации, Страница: 17 / 24

Поделиться
Скачать
Abicor Binzel ALPHA 1 Скачать руководство пользователя страница 17

17

Note: Most POROSITY is caused by gas problems, followed by base metal contamination

 Causes of Porosity

 

BASE METAL CONTAMINATION

Impurities on base metal.

 

FILLER METAL CONTAMINATION

Impurities on filler metal (wire). 

 

ATMOSPHERIC CONTAMINATION

Drafts, wind, fans, etc. 

 

GAS MIXING APPARATUS

1. Too high a gas flow, causing turbulence, 

  and/or sucking air at hose connections; 

  creating venturi effect at end of gas nozzle.

2. Too low a gas flow, causing insufficient gas 

 coverage. 

3. Damaged or kinked gas lines.

4. Too high an oxygen content. 

5. Leaks in gas distribution system. 

6. Other impurities in gas – moisture, etc. 

7. Inconsistent gas flow (cfh) at the torch 

 connection.

GAS TURBULENCE

1. excessive spatter build-up in gas nozzle and 

  on contact tip. 

2. Nozzle damage, causing uneven gas 

 coverage. 

3. Torch gas ports clogged or deformed. 

4. Super-heated nozzle, causing shielding gas 

  to expand rapidly and create return effect at 

  end of nozzle. Results in contamination of 

  gas by atmosphere. 

5. Gas diffuser/nozzle insulator missing. 

6. Too high a gas flow causing venturi effect. 

WELDING PARAMETERS, ETC.

1. Too long a wire stick-out; gas nozzle too far 

  from weld puddle. 

2. Bad torch position – too sharp a torch incline 

  causing venturi effect at the end of the nozzle 

  leading to atmospheric contamination. 

3. excessively wide weld pool for nozzle I.D. 

4. Arc voltage too high. 

5. Too high a travel speed.

 

Possible Solutions

 

a.  Remove contamination; clean surfaces 

b.  Use of specific wire/gas mix for specific 

 

types of impurities. 

a.  Replace wire. 

b.  Install wire-cleaning system. 

c.  Prevent industrial dust/dirt/grit from 

 

contaminating wire during storage or use. 

d.  Prevent build-up of aluminum oxide on 

 

exposed aluminum wire surface by using up 

 quickly. 

e.  Remove wire from wire drive unit and store 

 

in a sealed plastic bag when not in use for 

 

long periods.

 

a.  Protect weld from drafts (curtains/screens). 

b.  Use tapered or bottleneck gas nozzles when 

 

drafts cannot be avoided.

 

1a. Reduce gas flow.

1b. Tighten all hose connection points. 

2.  Increase gas flow. 

3.  Repair or replace 

4.  Adjust mixer. 

5.  Repair leaks. 

6.  Overhaul system; fit filters and/or dryers. 

7.  Regulate pressure into flow meter for 

 

consistent cfh delivery of gas. 

1.  Clean nozzle and tip regularly; spray with 

 

anti-spatter fluid. 

2.  Replace nozzle. 

3.  Clean or replace. 

4.  Check duty cycle rating of torch.

5. Replace. 

6.  Reduce gas flow. 

1.  Use longer nozzle or adjust stick-out (3/8” 

 

minimum or 15 times wire diameter). 

2.  Correct torch angle. 

3.  Width of the weld pool should be 1.3 times 

 

nozzle I.D.; Use suitable wider gas nozzle. 

4.  Reduce voltage. 

5.  Reduce speed. 

TROUBLESHOOTING: POROSITY (SUMMARY)

Содержание ALPHA 1

























Отзывы:

Нет отзывов