manualshive.com logo in svg

ABB SPA-ZC 302, Руководство по установке и пусконаладке

Поделиться
Скачать
ABB SPA-ZC 302 Скачать руководство пользователя страница 32

32

1MRS755014

Profibus-DPV1/SPA Gateway

Installation and Commissioning Manual

SPA-ZC 302

2. Ensure that the correct COM port is selected from the 

Settings > COM 

menu in 

PCT.

3. Also ensure that the gateway is in configuration mode. Configuration mode is 

enabled by using the DIP switches on the front of the gateway, see Section 
3.3.3.3. DIP switch configuration.

4. Select 

Device > Download

 configuration in the main menu. The configuration 

is now downloaded and a confirmation dialog is displayed. Click 

OK 

to confirm 

the download, see Fig. 4.4.-1.

A050353

Fig. 4.4.-1 Configuration download succeeded

This step is optional but it is a good practice to also download the configuration 
source to the gateway. In this way the gateway always contains all the necessary data 
that can be used in the future. The configuration archive can be downloaded as such 
or compressed to a zip file. After that, select 

Device > Download Archive

 

in the 

main menu and a file selection dialog is opened. Select the saved configuration that 
has been made for the gateway “<filename>.pcf” and click

 Open

. When this is done, 

the archive will be downloaded to the device and the a confirmation dialog is shown, 
see  Fig. 4.4.-2. Click 

OK

 to confirm the archive download. For more information 

on LEDs, see Section 8.4. Troubleshooting.

Fig. 4.4.-2 Archive download succeeded

The archive is stored in the device until another archive is downloaded and the new 
archive overwrites it.

5. In order to verify the signals that  are actually read from the protection relay:

•  The configuration is uploaded after the first start-up with the protection relay 

connected.

•  The state of the In Use flag is checked.

For details on how to do this, see Sections Section 4.7. In Use flags. 

Содержание SPA-ZC 302





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды