background image

ABB | SACE Tmax XT

140 | © 2019 ABB |  1SDH002039A1002 - ECN000093027 - Rev. A

External accessories | 7 - Ekip Com Modbus TCP

7 - Ekip Com Modbus TCP

 

Ekip Com Modbus TCP

 is a communication accessory which allows Ekip Touch to be integrated into an 

Ethernet network with Modbus TCP communication protocol, with remote supervision and monitoring 
functions in two different modes, standard and HTTP server.
The module is configured as master and remotely, you can:

•  read Ekip Touch measurements and information
•  manage certain controls, including opening and closing the actuator
•  access information and parameters not available on the display
•  If connected to a withdrawable version of the circuit-breaker, the allows the racked-in/racked-out status 

to be detected

 NOTE: 

the remote open and close commands of the circuit-breaker can only be executed if 

Ekip Touch is in the Remote configuration

 

The System Interface document is available for mapping the module in its communication network. All the 
required communication and command details are listed in the document (page 129).
Accessories 

Ekip Cartridge

 and 

Ekip Supply

 are required in order to connect 

Ekip Com Modbus TCP

 TM

 to 

Ekip Touch (page 130, 131).
Depending on the parameter settings, described in the next pages, the ports used by the module are:

Port

Service

Notes

502/tcp

Modbus TCP

Valid for the Modbus TCP mode

80/tcp

Server HTTP

Valid for the HTTP Server mode

319/udp

IEEE 1588

Valid with IEEE 1588 protocol enabled

20/udp
68/udp

DHCP client

DHCP client enabled alternatively as: 

Static address = On

Safety and cyber security

Since the module allows the actuator connected to Ekip Touch and access to the data in the unit to be 
checked, it can only be connected to networks equipped with all the necessary security and prevention 
measures against unauthorized access (for example, the network of the control system of an installation).

 IMPORTANT:

• 

it is the customer's sole responsibility to provide and continuously ensure a secure 
connection between the module and customer network or any other network (as the 
case may be). The plant manager must establish and maintain appropriate measures 
(such as but not limited to the installation of firewalls, application of authentication 
measures, encryption of data, installation of antivirus programs, etc.) to protect the 
product, the network, the customer system and interface against any kind of security 
breaches, unauthorized access, interference, intrusion, loss and/or theft of data or 
information.

 

ABB and its affiliates are not liable for damages and/or losses related to 

such security breaches, unauthorized accesses, interference, intrusion, loss and/or 
theft of data or information.

• 

The module cannot be connected directly to the Internet. Only connect to dedicated 
Ethernet networks

 

with Modbus TCP communication protocol

Models

Two different modules compatible with the Modbus TCP protocol are available: 

Ekip Com Modbus TCP

 and 

Ekip Com Modbus TCP Redundant

.

The modules are identical in terms of characteristics and installation methods, except for: display menus, 
cabling and addresses for system communication, which are specific for each module.

 NOTE: 

if different indications are not given, the information in the next chapter is valid for 

both models

The two modules can be connected at the same time to Ekip Touch so as to expand the potential of the unit 
(e.g. for applications where high grid reliability is required).

 

IMPORTANT: each Ekip Touch can be fitted with only one module per type. The 
configuration with two modules of the same model is not allowed (example: two Ekip 
Com Modbus TCP Redundant)

 

Содержание SACE Tmax XT5














































































































































































































Отзывы: