manualshive.com logo in svg

ABB RBIP-01, Руководство пользователя

Поделиться
Скачать
ABB RBIP-01 Скачать руководство пользователя страница 34

User interface

34

MS/TP submenu

When you select the 

MS/TP

 submenu, the 

MS/TP Settings

 page opens. It provides 

the settings for BACnet MS/TP.

MS/TP Settings page

If your BACnet router works in MS/TP, give the following settings:

MS/TP Settings

Description

Baud Rate

The baud rate in the MS/TP network

The potential values are: 9600, 19200, 38400, 57600, 76800 and 
115200 bit/s. The default value is 38400. 

Note that the 57600 and 115200 baud rates are not BACnet standard 
baud rates and all MS/TP implementations may not support them.

MAC Address

The MAC address of the router module in the MS/TP network. The 
router module acts as an MS/TP master node. 

The value is valid from 0 to 127 and the default value is 0.

Network Number

The network number of your local MS/TP network. The network number 
must be unique within the entire network.

The network number is valid in the range from 1 to 65.535. The default 
value is 2.

Содержание RBIP-01



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды