ABB RBIP-01 Скачать руководство пользователя | Manualshive

Страница: 17 / 58

background image

Quick start-up guide

17

Quick start-up guide

What this chapter contains

This chapter presents the steps to take during the start-up of the RBIP-01 BACnet/IP
Router Module and is intended for experienced professionals of IT and BACnet
communication. Detailed installation instructions of the module are given in

RBIP-01

BACnet/IP Router Module Installation Manual

(3AUA0000040168 Rev A [English]).

For more detailed commissioning instructions, refer to the following chapters.

Configuring RBIP-01 BACnet/IP Router Module settings

WARNING!

Before installation, switch off the drive power supply. Wait five minutes

to ensure that the capacitor bank of the drive is discharged. Switch off all dangerous
voltages connected from external control circuits to the inputs and outputs of the
drive. For more information, see chapter

Safety instructions

Note

: Do not connect the router module to the network before you have

commissioned the device!

1. Connect the crossover cable delivered in the router module package to the

module and your PC.

2. If not done, set your PC to run as a Dynamic Host Configuration Protocol

(DHCP) client or set the IP address of your PC manually to 192.168.0.2/
255.255.255.0.

• If you use DHCP, activate the DHCP server in the router module by pressing

and holding the Reset switch of the router module down for more than 5
seconds, but not longer than 10 seconds. As soon as the STATUS LED flashes
red and green alternating, the DHCP server is active.

3. In your web browser, enter the IP address

http://192.168.0.1

and login to the

router module using the user name/password combination

admin/admin

. For

supported browsers, see

RBIP-01 BACnet/IP Router Module Installation Manual

(3AUA0000040168 Rev A [English]).

4. Open the

Assistant

menu. Go through all its pages from left to right and apply

the settings according to your BACnet project. Confirm all settings on each page
by clicking the

Save

button.

5. On the

Activate

page, activate the configuration by clicking

Activate and

Restart

. Restarting the router module takes 25 seconds.

6. If you changed the IP address of the router module, adjust the IP address

settings of your PC accordingly.

«
...
15
16
17
18
19
...
»

Содержание RBIP-01



























































Отзывы:

Нет отзывов

Похожие инструкции для RBIP-01

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: Samson Страницы: 40

Бренд: IAI Страницы: 5

FEBCO 860 Small Series

Бренд: Watts Страницы: 12

Бренд: Bardiani Valvole Страницы: 54

Бренд: Parker Страницы: 478

Бренд: DSE Страницы: 2

Бренд: Warner Electric Страницы: 4

Бренд: hager Страницы: 4

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренд: Aqua Lung Страницы: 24

Бренд: Osaka Страницы: 12

Бренд: Lika Страницы: 28

Бренд: C-TEC Страницы: 28

Бренд: P.A. Страницы: 3

Бренд: rotork Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды