ABB OmniCore V250XT Скачать руководство пользователя страница 397

Страница: 397 / 456

LEDs

The illustration below shows the indication LEDs on the Ethernet switch.

xx1800000584

Status LED

Significance

Description

Startup sequence:

No color: Input voltage is outside specified voltage or internal fault
in the switch.

Green, solid: The switch is operational.

If the LED does not turn steady green, the status indicator LED can be
used to identify the following issues:

Status LED

Fault indication:

•

No color: If input voltage is within specified voltage limits and the
LED is not lit then replace the switch.

Shows the status of Ethernet links.

Ethernet LEDs

Green:

•

Off:10 Mbps data rate is selected.

•

On:100/1000 Mbps data rate is selected.

Yellow:

•

Flashing: The Ethernet is active on link.

•

Solid: A LAN link is established.

•

Off: A LAN link is

not

established.

Product manual - OmniCore V250XT

397

3HAC073447-001 Revision: B

7 Troubleshooting

7.3.7 Troubleshooting the Ethernet switch

Continued

Содержание OmniCore V250XT








































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V250XT

Отзывы:

ABB OmniCore V250XT, Руководство по эксплуатации продукта, Страница: 397 / 456

Результаты поиска

Содержание OmniCore V250XT

Отзывы: