ABB OmniCore V250XT страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 456

background image

1.3.3 Enabling device and hold-to-run functionality

Three-position enabling device

CAUTION

The person using the three-position enabling device is responsible to observe
the safeguarded space for hazards due to robot motion and any other hazards
related to the robot.

The three-position enabling device is located on the FlexPendant. When
continuously held in center-enabled position, the three-position enabling device
will permit robot motion and any hazards controlled by the robot. Release of or
compression past the center-enabled position will stop the robot motion.

CAUTION

For safe use of the three-position enabling device, the following must be
implemented:

•

The three-position enabling device must never be rendered inoperational
in any way.

•

If there is a need to enter safeguarded space, always bring the FlexPendant.
This is to enforce single point of control.

Hold-to-run function in manual high speed mode

The hold-to-run function for manual high speed allows movement in conjunction
with the three-position enabling device when the button connected to the function
is actuated manually. This hold-to-run function can only be used in manual high
speed mode. In case of hazard, release or compress the three-position enabling
device.

How to use the hold-to-run function for manual high speed mode is described in
the operating manual for the controller.

Note

The manual high speed mode is not available in all markets.

Product manual - OmniCore V250XT

23

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

1 Safety

1.3.3 Enabling device and hold-to-run functionality

«
...
21
22
23
24
25
...
»

Содержание OmniCore V250XT









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OmniCore V250XT

Бренд: Makeblock Страницы: 14

Бренд: Pololu Страницы: 85

Бренд: RoboTiCan Страницы: 10

YCOO Bionic Biopod InMotion Cyberpunk

Бренд: Silverlit Страницы: 2

Heavy Payload Series

Бренд: TM Robot Страницы: 87

Бренд: REVELL Страницы: 8

HEXBUG VEX ROBOTICS CROSSBOW 406-6533

Бренд: Innovation First Страницы: 31

Бренд: Xtrem Bots Страницы: 52

Бренд: Same Toy Страницы: 56

Бренд: ABB Страницы: 730

FlexLoader SC 6000

Бренд: ABB Страницы: 284

Feather Duster V2

Бренд: ABB Страницы: 192

Бренд: ABB Страницы: 770

Бренд: ABB Страницы: 766

FlexTrack IRT501 Series

Бренд: ABB Страницы: 204

Fronius TPS 320i

Бренд: ABB Страницы: 88

Бренд: ABB Страницы: 76

FlexLoader Vision

Бренд: ABB Страницы: 288

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды