ABB OmniCore V250XT страница 106 Скачать руководство пользователя

Страница: 106 / 456

Use this procedure to configure the robot stopping functions in Visual SafeMove.

1 In

Visual SafeMove

, select

Stop Configuration

xx2100000737

2 Select a stop configuration and define the mode (automatic or manual).

•

ProtectiveStop

is the AS/GS input

•

ExternalEmergencyStop

is the ES input

To avoid dead-lock in an emergency stop chain, the

ExternalEmergencyStop

input can be decoupled from the ES output.

•

LocalEmergencyStop

is the emergency stop device on the FlexPendant

3 Select the stop category.

For some manipulators, only category 1 stop is available.

4 After the configuration is done, the safety configuration must be written to

the controller and then a restart of the controller is required.

Tip

Содержание OmniCore V250XT








































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V250XT

Отзывы:

Похожие инструкции для OmniCore V250XT

Бренды по названию

Популярные бренды

ABB OmniCore V250XT, Руководство по эксплуатации продукта

Результаты поиска

Содержание OmniCore V250XT

Отзывы:

Похожие инструкции для OmniCore V250XT

Бренды по названию

Популярные бренды