ABB i-bus KNX SUG/U 1.1 Скачать руководство пользователя страница 40

Страница: 40 / 56

ABB i-bus

KNX

Commissioning

38 2CDC508171D0201 | SUG/U 1.1

No.

Function

Group object name

Data type

Flags

Status Fan speed

Split unit

1 byte

DPT 5.001

C, R, T

Dependent on parameter

Enable group object "Status Fan speed" 1 byte

The fan speed status is always shown by the 1 byte object, even if Control fan speed with object parameter is set to

1 bit

up/down

on the

Split Unit settings

page.

The coding of the status object is dependent on the setting in the

Coding of 1 byte

parameter.

0%=Auto; 33%=Low, 66%=Medium, 100%=High

Status Fan speed

Split unit

1 byte

DPT 5.010

C, R, T

Dependent on parameter

Enable group object "Status Fan speed" 1 byte

The fan speed status is always shown by the 1 byte object, even if Control fan speed with object parameter is set to

1 bit

up/down

on the

Split Unit settings

page.

The coding of the status object is dependent on the setting in the

Coding of 1 byte

parameter.

0=Auto, 1=Low, 2=Med, 3=High

Fan up/down

Split unit

1 bit

DPT 1.007

C, W

Dependent on parameter

Control fan speed with object

When a telegram is received on this object, the fan speed reduces or increases by one speed.

Value 1: Increases fan speed

Value 0: Reduces fan speed

Available fan speeds are: Automatic, Low, Medium, High

If the fan reaches High, a further telegram with the value 1 has no effect.

If the fan is set to Automatic, a further telegram with the value 0 has no effect.

Operation mode

Split unit

1 byte

DPT 20.105

C, W

Dependent on parameter

Always visible

This object sets the operating mode for the split unit.

The operating modes set on receipt of a corresponding value are as follows:

0=Auto

1=Heating

3=Cooling

9=Ventilation

14=Drying

All other values are discarded.

Содержание i-bus KNX SUG/U 1.1

























































Результаты поиска

Содержание i-bus KNX SUG/U 1.1

Отзывы:

ABB i-bus KNX SUG/U 1.1, Руководство по эксплуатации продукта, Страница: 40 / 56

Результаты поиска

Содержание i-bus KNX SUG/U 1.1

Отзывы: