ABB GSB 800 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 32

ABB GSB 800 Скачать руководство пользователя страница 27

TR A N S FOR M E R BUS H I NG S T YPE G S B 8 0 0

I N S TA L L AT I O N A N D M A I N T EN A N C E G U I D E

27

Mount the outer terminal in accordance with section 2.12.

Place the bushing in the crate on the two supports; see
Fig. 39. Make sure that the flange is inserted in the slot in the
corresponding support to prevent the busing from sliding
axially in the crate during transportation. This will also
ensure that the top piece is correctly positioned at the top
end support in the crate. The previous mentioned support
for flange is made of two parts and after placing the
bushing in the lower part the supports upper half shall be
placed on the top side of the flange and secured by wood
screws; Fig. 40. Also the top of the bushing shall be fixed by
a clamping strap to the top end support which is a one piece
support contrary to the flange support; Fig. 41. Lift the top
cover in its straps and attach it to the box with screws;
Fig. 42.

—
39 Place the bushing in its crate on the two supports.

—
40 Secure the bushing and support block with screws from the outside.

—
41 Tighten the clamping strap at top end.

—
42 Remounting the top cover.

«
...
25
26
27
28
29
...
»

Содержание GSB 800

































Отзывы:

Нет отзывов