ABB GSB 800 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

ABB GSB 800 Скачать руководство пользователя страница 13

TR A N S FOR M E R BUS H I NG S T YPE G S B 8 0 0

I N S TA L L AT I O N A N D M A I N T EN A N C E G U I D E

13

Lo

w

er dra

w

-r

od

Upper dra

w

-r

od

2.10 Draw-rod system

The draw-rod system can be divided level with the mounting
flange. Fig. 16 shows the draw-rod system and the joints
that are locked at delivery.

The additional joint at flange level must be locked with
locking fluid (Loctite 242 and activator Loctite T747) on site.
The threads must be degreased before applying the locking
fluid.

Supporting the lower draw-rod during transportation

The lower draw-rod can be used for supporting the bottom
contact and the cables in the transformer tank during
transport of the transformer/reactor, as shown in Fig. 15.

Mounting of the draw-rod must be performed
according to the described procedures.

Additional joint
on request

Standard joint,
locked at delivery

Standard joint at
flange level, lower
thread unlocked at
delivery

Locked with
locking fluid at
delivery

Lower thread
unlocked at
delivery

Threaded sleeve
M10 x 30 mm

Transport
cover

Standard
end-shield

Transformer
/reactor

Cables

—
15 Lower draw-rod support during transportation.

—
16 Joints of the draw-rod system.

«
...
11
12
13
14
15
...
»

Содержание GSB 800

































Отзывы:

Нет отзывов