ABB GSB 800 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

ABB GSB 800 Скачать руководство пользователя страница 19

TR A N S FOR M E R BUS H I NG S T YPE G S B 8 0 0

I N S TA L L AT I O N A N D M A I N T EN A N C E G U I D E

19

2.10.3 Lifting of bushing for mounting on transformer

Alternative 1: Raising the bushing to a vertical position.

1. Place soft bedding - e.g. a rubber mat or a wooden board

- under the bottom end of the bushing to avoid damage
to the bottom contact or center tube.

2. When raising the bushing to a vertical position, the

lifting gear must be arranged according to Fig. 25.

CAUTION

The bushing

must not

be lifted by the insulator.

Alternative 2: Raising the bushing to a specific angle.

1. Place soft bedding - e.g. a rubber mat or a wooden board

- under the bottom end of the bushing to avoid damage
to the bottom contact or center tube.

2. When raising the bushing to a specific angle, the lifting

gear and tackle must be arranged according to Fig. 26.

CAUTION

The bushing

must not

be lifted by the insulator.

Lifting gear
1ZSC004867-AAA

Tackle

Lifting gear
1ZSC004867-AAA

Soft bedding

Soft bedding

Lifting adapter
1ZSC004867-AAB

Lifting adapter
1ZSC004867-AAB

min 70

°

—
25 Alternative 1: Raising the bushing to a vertical position.

—
26 Alternative 2: Raising the bushing to a specific angle.

«
...
17
18
19
20
21
...
»

Содержание GSB 800

































Отзывы:

Нет отзывов