manualshive.com logo in svg

ABB GSB 800, Руководство по установке и обслуживанию, Страница: 23 / 32

Поделиться
Скачать
ABB GSB 800 Скачать руководство пользователя страница 23

TR A N S FOR M E R BUS H I NG S T YPE G S B 8 0 0 

I N S TA L L AT I O N  A N D  M A I N T EN A N C E  G U I D E

23

2.13 Oil-filling of voltage tap housing

The GSB 800 bushing is equipped with a voltage tap, 
providing a voltage source while the bushing is in operation.

The voltage tap housing should be filled with oil when the 
continuous voltage exceeds 600 V. For voltages below 600 V, 
the voltage tap housing does not need to be oil filled.

The voltage tap housing should be filled with clean and dry 
transformer oil. This will prevent corrosion and 
condensation. Fill the tap housing as follows:
1.  Remove the sealing plug on the top of the voltage tap; 

see Fig. 32.

2.  Fill the tap housing, leaving a space of approximately 

6-10 mm for oil expansion.

3.  Firmly tighten the sealing plug.

The voltage tap adapter is used for permanent connection 
to measuring circuits; see Fig. 33.

WARNING

The voltage tap adapter must be equipped with 
suitable over-voltage protection to prevent damage 
during service. The cable gland must be oriented 
downwards in order to prevent water from entering 
the equipment. 

If the connected impedance is too high, it can cause over-
voltages on the voltage tap adapter during transient 
conditions leading to flashover. It is important to use the 
correct impedance for the actual transient frequencies at 
the installation on site.

Contact the supplier for more detailed information.

Sealing plug

Voltage tap housing

Voltage 
tap cover

Gasket

Gasket (O-ring)

Thread Pr 22.5 (Pg 16 acc. to 
DIN 40430). Turnable.

—
32 Voltage tap.

—
33 Voltage tap adapter.

Содержание GSB 800

































Отзывы:

Нет отзывов