ABB GSB 800 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

ABB GSB 800 Скачать руководство пользователя страница 14

14

TR A N S FOR M E R BUS H I NG S T Y PE G S B 8 0 0

I N S TA L L AT I O N A N D M A I N T EN A N C E G U I D E

2.10.1 Installation of standard end-shield

Alternative 1: Mounting the standard end-shield on the
bottom contact adapter. Fig. 17.

1. Mount the socket screws with springs to the bottom

contact adapter.

2. Connect the cable lugs to the bottom contact.

Tightening torque 68 ± 6 Nm.

3. Push the end-shield gently against the bottom contact

adapter, guiding the socket screws through the key
holes.

4. While applying force, turn the end-shield clockwise

approximately 20° and then release when in locked

position.

Alternative 2: Mounting the standard end-shield on the
bottom contact. Fig. 18.

1. Mount the socket screws with springs to the bottom

contact.

2. Connect the cable lugs to the bottom contact.

Tightening torque 68 ± 6 Nm.

3. Push the end-shield gently against the bottom contact,

guiding the socket screws through the key holes.

4. While applying force, turn the end-shield clockwise

approximately 20° and then release when in locked

position.

Socket
screw
with
spring

Socket screw
with spring

—
17 Alternative 1: Mounting the standard end-shield on the bottom contact adapter.

—
18 Alternative 2: Mounting the standard end-shield on the bottom contact.

«
...
12
13
14
15
16
...
»

Содержание GSB 800

































Отзывы:

Нет отзывов