ABB GSB 800 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

ABB GSB 800 Скачать руководство пользователя страница 15

TR A N S FOR M E R BUS H I NG S T YPE G S B 8 0 0

I N S TA L L AT I O N A N D M A I N T EN A N C E G U I D E

15

Flexible pull-through cord

2.10.2 Docking of bushing to transformer

1. Completely remove the outer terminal.
2. Mount the lifting gear (1ZSC004867-AAA) and the lifting

adapters (1ZSC004867-AAB) according to Fig. 29. Also
see section 2.10.3.

3. Pull the flexible pull-through cord through the bushing

Lifting gear 1ZSC004867-AAA

Upper
draw-rod

Lifting adapters
1ZSC004867-AAB

Joint at
flange level

until it is visible on the oil-side and connect it to the top
of the upper draw-rod.

4. The upper draw-rod is now pulled through the bushing,

leaving the joint at flange level hanging outside the
conductor tube or the standard end-shield on the oil-
side.

5. Raise the bushing according to steps 1 and 2 in Section

2.10.3.

—
19 Installation of draw-rod into bushing, using pull-through cord, lifting adapters and lifting gear. The right view shows the bushing after mounting.

«
...
13
14
15
16
17
...
»

Содержание GSB 800

































Отзывы:

Нет отзывов