ABB DPA UPScale ST120 Скачать руководство пользователя

Страница: 3 / 129

Modifications reserved

Page 3/79

Contents

Safety regulation ....................................................................................... 6

Safety rules .......................................................................................................... 6

1.2

Safety symbols and warnings ............................................................................. 7

General information ................................................................................... 8

2.1

Declaration of safety conformity and CE marking .............................................. 8

2.2

Nameplate and identification .............................................................................. 9

System description.................................................................................. 10

3.1

System architecture ........................................................................................... 11

3.2

Main elements description ................................................................................ 12

3.2.1

Single line diagram ......................................................................................................................... 12

3.2.2

Functional description .................................................................................................................... 12

3.2.3

Control and monitoring .................................................................................................................. 14

3.3

Multi cabinet configuration ............................................................................... 15

3.4

Operating modes ............................................................................................... 16

3.4.1

Mode “ON-LINE” ........................................................................................................................... 16

3.4.2

Mode “OFF-LINE” (Eco or bypass mode)........................................................................................ 17

3.4.3

Mode “ON-BATTERY” (Battery mode) ............................................................................................ 18

3.4.4

Maintenance bypass ...................................................................................................................... 19

Packing, transportation & storage .......................................................... 20

4.1

Packing & transportation ................................................................................... 21

4.2

Unpacking .......................................................................................................... 22

4.2.1

Standard package (film) ................................................................................................................. 22

4.2.2

Sea freight light package (cardboard box) ...................................................................................... 23

4.2.3

Sea freight cases (wooden box) ..................................................................................................... 24

4.3

Storage ............................................................................................................... 25

4.3.1

UPS ............................................................................................................................................... 25

4.3.2

Batteries ........................................................................................................................................ 25

Installation ............................................................................................... 26

5.1

Environmental condition .................................................................................... 26

5.1.1

Climatic conditions ......................................................................................................................... 26

5.1.2

Biological conditions ...................................................................................................................... 26

5.1.3

Mechanical active substance .......................................................................................................... 26

5.1.4

Chemical active substance ............................................................................................................. 26

5.1.5

Mechanical conditions .................................................................................................................... 26

5.2

Enviromental condition for UPS with inside battery modules ......................... 26

5.2.1

Climatic conditions ......................................................................................................................... 26

5.3

UPS and battery location .................................................................................. 27

5.4

UPS connections ............................................................................................... 28

Содержание DPA UPScale ST120




























































































































Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды

ABB DPA UPScale ST120, Руководство пользователя

Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды