ABB DPA UPScale ST120 Скачать руководство пользователя | Manualshive

Страница: 28 / 129

background image

Modifications reserved

Page 28/79

5.4

UPS connections

The customer has to supply the wiring to connect the UPS to the local power source (see chapter
5.7). The electrical installation procedure is described in the following text. The installation inspection

and initial start-up of the UPS and extra battery cabinet must be carried out by qualified service

personnel, such as a licensed service engineer from the manufacturer or from an agent certified by

the manufacturer.

WARNING!

THE INSTRUCTIONS IN THIS USER MANUAL HAVE TO BE FOLLOWED

ALWAYS IN ORDER TO AVOID INJURIES FROM ELECTRICAL SHOCK.

WARNING!

ALL THE OPERATIONS DESCRIBED IN THIS MANUAL MUST BE
PERFORMED BY CERTIFIED ELECTRICIANS OR BY QUALIFIED INTERNAL

PERSONNEL.
DO NOT OPERATE IF WATER OR MOISTURE IS PRESENT.

BY OPENING OR REMOVING THE UPS COVERS YOU RUN THE RISK OF
EXPOSURE TO DANGEROUS VOLTAGES.

PHYSICAL INJURY OR DEATH MAY FOLLOW, OR DAMAGE MAY OCCUR
TO THE UPS OR THE LOAD EQUIPMENT IF THESE INSTRUCTIONS ARE

IGNORED.

To ensure correct operation of the UPS and its ancillary equipment, it is necessary to provide the

mains cables with appropriate fuse protection. See chapter 5.7.1.

The UPS unit has the following power connections:

Rectifier (In) : Three-phase (1L1, 1L2, 1L3), Neutral (1N) and protective earth (PE)

connection for the

rectifier input

Bypass (In) :

Three-phase (2L1, 2L2, 2L3), Neutral (2N)

connection for the

bypass if used as Dual Feed input

Load (Out) :

Three-phase (3L1, 3L2, 3L3), Neutral (3N) and protective earth (PE)

connection for the

load output

External Battery : Plus (+), Common (N), Minus (-) and protective earth (PE)

connection for the

external batteries

IMPORTANT

NOTE

INPUT NEUTRAL IS REQUIRED TO OPERATE THE RECTIFIER.

In TN-S Systems, no 4-pole input switches or circuit breakers should be used. If you
have to use a 4-pole switch for another reason, you have to be aware that, when open,
the system - UPS and all downstream equipment - are floating against the PE.

Fig 5.4-1: Input neutral

«
...
26
27
28
29
30
...
»

Содержание DPA UPScale ST120


































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPA UPScale ST120

Бренд: Staco Energy Страницы: 26

Бренд: G-Tec Страницы: 50

Бренд: Unitek Страницы: 28

Бренд: Sola Страницы: 18

Uninterruptible Power Supply SOLA 4000

Бренд: Sola Страницы: 108

Бренд: PowerWalker Страницы: 5

UPSPro UPS-ST-600

Бренд: TYCON Solar Страницы: 8

SmartPro SMART750RM1U

Бренд: Tripp Lite Страницы: 5

Бренд: Xtreme Power Conversion Страницы: 48

Бренд: Xtreme Power Conversion Страницы: 77

Extreme Value Tower XVT-600

Бренд: Rackmount Страницы: 4

Бренд: ICA Страницы: 8

Lifeline M95-600 Series

Бренд: ICS Страницы: 14

Бренд: Eaton Страницы: 26

Бренд: Eaton Страницы: 8

Protect 3.M 2.0

Бренд: AEG Страницы: 4

Бренд: Para systems Страницы: 16

Бренд: Para systems Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды