ABB DPA UPScale ST120 Скачать руководство пользователя

Страница: 53 / 129

Modifications reserved

Page 53/79

7.2

Shut-down procedure

WARNING!

THE OPERATIONS DESCRIBED IN THIS CHAPTER MUST BE PERFORMED
BY A SERVICE ENGINEER FROM THE MANUFACTURER OR FROM AN
AGENT CERTIFIED BY THE MANUFACTURER

The

DPA UPScale

may be shut down completely if the load does not need input power for an

extended period.
It may be switched to maintenance bypass mode for service or maintenance purposes, or transferred

to the off-line mode (ECO-mode) if the load does not need the highest degree of protection.

The load may be disconnected by means of the two ON/OFF (LOAD-OFF) buttons.

Complete shutdown procedure for DPA UPScale

The UPS should only be shut down when there is no need to supply the load. The following

procedures can only be executed after the load has been completely de-energized.

NOTE

IF A PARALLEL UPS HAS TO BE TURNED OFF, THEN BOTH ON/OFF

BUTTONS ON ALL UPS MODULES HAVE TO BE PUSHED. IN THIS CASE,
THE POWER SUPPLY TO THE LOAD WILL BE INTERRUPTED

Verify that the loads are shut down and that there is no need for power supply to the load.

If the loads are all disconnected, press simultaneously both ON/OFF-Buttons on UPS-control

panel on all control panels on each module.

On the LCD: “LOAD OFF, SUPPLY FAILURE” will appear and the LED-indicator will indicate

as shown below:

LED Indicator

Color

LINE 1

Green

LINE 2

OFF

BYPASS

OFF

INVERTER

OFF

BATTERY

Green

Open battery fuses/breakers on internal (if any) and external battery cabinets or racks.

Open the mains fuses/breaker in the building distribution panel.

NOTE

MAKE SURE THE INTERNAL DC-CAPACITORS (ELCO) HAVE BEEN

DISCHARGED BY WAITING AT LEAST 10 MINUTES AFTER SHUTDOWN.

THE DPA UPAScale

IS NOW VOLTAGE FREE.

Содержание DPA UPScale ST120




























































































































Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды

ABB DPA UPScale ST120, Руководство пользователя

Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды