ABB DPA UPScale ST120 Скачать руководство пользователя

Страница: 26 / 129

Modifications reserved

Page 26/79

Installation

5.1

Environmental condition

The UPS is designed for indoor location, in a restricted access location only and should be located as

follows:

5.1.1

Climatic conditions

Ambient temperature

0 to +40

Relative humidity

Conditions of condensation

Presence of wind-driven rain,

snow, hail, etc

Conditions of water from sources

other than rain

Icing conditions

The climate control system could be periodically switched on or off, but extremely high or low

temperatures should be avoided.

5.1.2

Biological conditions

Flora (presence of mould, fungus)

Fauna (presence of rodents and other animals)

The location should not have a particular risk of biological attacks.

5.1.3

Mechanical active substance

The UPS shall not be placed in proximity to a source of sand or dust.

5.1.4

Chemical active substance

The location can have a normal level of contaminants experienced in urban areas over the whole area.

5.1.5

Mechanical conditions

The UPS shall be placed in a location with no significant exposure to vibration and shock.

5.2

Enviromental condition for UPS with inside battery modules

As the battery life depends on the ambient temperature, for the UPS with internal battery modules it is
recommended to have a location with a climate-controlled system to maintain the conditions as

follows:

5.2.1

Climatic conditions

Ambient temperature

Содержание DPA UPScale ST120




























































































































Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды

ABB DPA UPScale ST120, Руководство пользователя

Результаты поиска

Содержание DPA UPScale ST120

Отзывы:

Похожие инструкции для DPA UPScale ST120

Бренды по названию

Популярные бренды