ABB ACS 140 Скачать руководство пользователя страница 65

Страница: 65 / 70

APPENDIX

Local Control vs. Remote Control

The ACS 140 can be controlled from two remote control locations or from the
control panel. Figure 17 below shows the ACS 140 control locations.

The selection between local control (LOC) and remote control (REM) can be
done by pushing the MENU and ENTER buttons simultaneously.

Figure 17 Control locations.

Local Control

The control commands are given explicitly from the control panel when the
ACS 140 is in local control. This is indicated by LOC on the control panel
display.

Parameter 1101

KEYPAD

REF

SEL

is used to select keypad reference, which

can be either

REF

1 (Hz) or

REF

2 (%). If

REF

1 (Hz) is selected, the type of

reference is frequency and it is given to the ACS 140 in Hz. If

REF

2 (%) is

selected, the reference is given in per cent.

If PID Control macro is used, reference

REF

2 is fed directly to the PID

controller as percentage. Otherwise, reference

REF

2 (%) is converted to

frequency so that 100 % corresponds to

MAXIMUM

FREQ

(parameter 2008).

Start/Stop/Direction,

EXT

Start/Stop/Direction,
Keypad Reference 1 (

REF

1, Hz)

(17(5

0(18

/2&5(0

mAVs

6(7

OUTPUTPAR MENU FWDREV

Crpm

REM

LOC

kHz

/2& 5(0

or Keypad Reference 2 (

REF

2, %)

External Reference 1 (Hz)

External Reference 2 (%)

OUTPUT

LOC

Содержание ACS 140







































































Результаты поиска

Содержание ACS 140

Отзывы:

ABB ACS 140, Руководство по программированию, Страница: 65 / 70

Результаты поиска

Содержание ACS 140

Отзывы: