ABB ACS 140 Скачать руководство пользователя страница 14

Страница: 14 / 70

Diagnostics

The control panel displays the following alarm and fault codes.

Alarms AL1-7 arise from button operation. Green LED blinks for AL10-21,
meaning that the ACS 140 cannot fully follow the control commands.

Table 1 Alarms.

Code

Description

AL 1

Parameter upload/download failed.

AL 2

Operation not allowed while start is active.

AL 3

Operation not allowed in current control mode (Local or Remote).

AL 5

Start/Stop/Direction or reference from control panel is not followed. Possible
causes:
• Remote mode: parameters disable the buttons (See APPENDIX.)
• Local mode: START/STOP button interlocked from digital inputs.

AL 6

Operation not allowed. Parameter 1602

PARAMETER

LOCK

is active.

AL 7

Use of factory macro disables operation.

AL10

Overcurrent controller active.

AL11

Overvoltage controller active.

AL12

Undervoltage controller active.

AL13

Direction lock. See parameter 1003

DIRECTION

AL14

Serial communication loss alarm.

AL15

Modbus exception response is sent through serial communication.

AL16

Analogue input 1 loss. Analogue input 1 value is less than

MINIMUM

AI1

(1301). See also parameter 3001

MIN

FUNCTION

AL17

Analogue input 2 loss. Analogue input 2 value is less than

MINIMUM

AI2

(1306). See also parameter 3001

MIN

FUNCTION

AL18

Panel loss. Panel is disconnected when Start/Stop/Dir or reference is
coming from panel. See parameter 3002

PANEL

LOSS

and APPENDIX.

AL19

Hardware overtemperature (at 95 % of the trip limit).

AL20

Motor overtemperature (at 95 % of the trip limit).

AL21

Motor stall alarm. See parameter 3009

STALL

FUNCTION

Содержание ACS 140







































































Результаты поиска

Содержание ACS 140

Отзывы:

ABB ACS 140, Руководство по программированию, Страница: 14 / 70

Результаты поиска

Содержание ACS 140

Отзывы: