ABB ACS 140 Скачать руководство пользователя страница 35

Страница: 35 / 70

ARAME

Group 99: Start-up Data

The Start-up Data parameters are a special set of parameters for setting up
the ACS 140 and for entering motor information.

Figure 1 Output voltage as a function of output frequency.

Code Description

9902

APPLIC MACRO
Application macro selection. This parameter is used to select the Application
Macro which will configure the ACS 140 for a particular application. Refer to
Application Macros

starting page 13, for a list and description of available

Application Macros.

9905

MOTOR NOM VOLT
Nominal motor voltage from motor rating plate. This parameter sets the
maximum output voltage supplied to motor by ACS 140.

MOTOR

NOM

FREQ

sets

the frequency at which output voltage is equal to the

MOTOR

NOM

VOLT

. The

ACS 140 cannot supply the motor with a voltage greater than the mains voltage.
See Figure 8.

9906

MOTOR NOM CURR
Nominal motor current from rating plate. The allowed range is 0.5 · I

... 1.5 · I

of ACS 140.

9907

MOTOR NOM FREQ
Nominal motor frequency from rating plate (field weakening point).
See Figure 8.

9908

MOTOR NOM SPEED
Nominal motor speed from rating plate.

Output voltage

Output frequency

MOTOR

NOM

VOLT

MOTOR

NOM

FREQ

Содержание ACS 140







































































Результаты поиска

Содержание ACS 140

Отзывы:

ABB ACS 140, Руководство по программированию, Страница: 35 / 70

Результаты поиска

Содержание ACS 140

Отзывы: