ABB ACS 140 Скачать руководство пользователя страница 61

Страница: 61 / 70

ARAME

4009

ACT1 MINIMUM
Minimum value for actual value 1 (

ACT

1). The setting range is -1000 to +1000 %.

Refer to Figure 15 and to Group 13 parameters for analogue input minimum and
maximum settings.

4010

ACT1 MAXIMUM
Maximum value for actual value 1 (

ACT

1). The setting range is -1000 to +1000

%. Refer to Figure 15 and to Group 13 parameters for analogue input minimum
and maximum settings.

4011

ACT2 MINIMUM
Minimum value for actual value 2 (

ACT

2). Refer to parameter 4009.

4012

ACT2 MAXIMUM
Maximum value for actual value 2 (

ACT

2). Refer to parameter 4010.

Figure 15 Actual value scaling. The range of the analogue input signal is set
by parameters 1301 and 1302 or parameters 1304 and 1305, depending on
the analogue input used.

Code Description

ACT

1 (%)

Analogue

ACT1

AI min

AI max

input signal

MINIMUM

MAXIMUM

ACT

1 (%)

Analogue

ACT1

AI min

AI max

input signal

MAXIMUM

MINIMUM

Содержание ACS 140







































































Результаты поиска

Содержание ACS 140

Отзывы:

ABB ACS 140, Руководство по программированию, Страница: 61 / 70

Результаты поиска

Содержание ACS 140

Отзывы: