ABB ACS 140 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 70

ABB ACS 140 Скачать руководство пользователя страница 12

4

Output Display

When the control panel is powered up, the panel displays the actual output
frequency. Whenever the MENU button is pressed and held, the control
panel resumes this OUTPUT display.

To toggle between output frequency and output current, press the UP or
DOWN button.

To set the output frequency, press ENTER. Pressing the UP/DOWN buttons
changes the output immediately. Press ENTER again to return to OUTPUT
display.

Menu Structure

ACS 140 has a large number of parameters. Of these, only the so-called
basic parameters are initially visible. The menu function -LG- is used to
make the full parameter set visible.

Setting Parameter Value

Press ENTER to view the parameter value.
To set a new value, press and hold ENTER until SET is displayed.

Note! SET blinks, if the parameter value is altered. SET is not displayed, if
the value cannot be altered.
Note! To view the parameter default value, press the UP/DOWN buttons
simultaneously.

OUTPUT

Hz

6(7

OUTPUT

Hz

OUTPUT

A

(17(5

(17(5

(17(5

LOC

LOC

LOC

OUTPUT display

Parameter groups

Parameters

OUTPUT

Hz

LOC

LOC

MENU

LOC

(17(5

0(18

0(18

0(18

PAR

6(7

s

0(18

(17(5

(17(5

CANCEL

STORE

«
...
10
11
12
13
14
...
»

Содержание ACS 140







































































Отзывы:

Нет отзывов