manualshive.com logo in svg

ABB ACS 140, Руководство по программированию, Страница: 46 / 70

Поделиться
Скачать
ABB ACS 140 Скачать руководство пользователя страница 46

38

Group 15: Analogue Output

Analogue output is used to output the value of any parameter of the 
Operating Data group (Group 1) as a current signal. Output current minimum 
and maximum values are configurable, as are the allowed minimum and 
maximum values for the observed parameter. 

If analogue output content maximum value (parameter 1503) is set to less 
than minimum value (parameter 1502), output current is inversely 
proportional to the value of the observed parameter.

 

Figure 5  Analogue output scaling.

Code Description

1501

AO CONTENT
Content for analogue output. Number of any parameter of the Operating Data 
group (Group 01).

1502

AO CONTENT MIN
Analogue output content minimum. Display depends on parameter 1501.

1503

AO CONTENT MAX
Analogue output content maximum. Display depends on parameter 1501.

1504

MINIMUM AO
Minimum output current.

1505

MAXIMUM AO
Maximum output current.

1506

AO FILTER
Filter time constant for AO.

1505

1504

1503

1502

AO content

AO (mA)

1505

1504

1503

1502

AO (mA)

AO content

Содержание ACS 140







































































Отзывы:

Нет отзывов