manualshive.com logo in svg

ABB AC 800M, Аппаратное обеспечение и эксплуатация

Поделиться
Скачать
ABB AC 800M Скачать руководство пользователя страница 213

Appendix E  Standards

Hazardous Location Approval

3BSE 027 941 R301

213

 

Appendix E  Standards

The information below is applicable to products approved for hazardous locations 
according to CSA and/or UL standards (UL1604).

Hazardous Location Approval

To comply with CSA and/or UL certification for use at hazardous locations, the 
following information becomes part of the product literature for CSA and/or 
UL-certified ABB industrial control products.

•

Equipment labeled with reference to Class I, Groups A, B, C and D, Division 2, 
hazardous locations is suitable for use in Class I, Division 2, Groups A, B, C, D 
or non-hazardous locations only.

•

The products having the appropriate CSA and/or UL markings (that is, Class I 
Division 2, Groups A, B, C, D), are certified for use in other equipment where 
the suitability of combination (that is, application or use) is determined by the 
CSA and/or UL or the local inspection office having jurisdiction.

Explosion hazard - Substitution of components may impair suitability for Class I, 
Division 2.

Explosion hazard - Do not replace batteries unless the power has been switched 
off or the area is known to be non-hazardous.

Explosion hazard - Do not disconnect equipment unless the power has been 
switched off or the area is known to be non-hazardous.

Содержание AC 800M







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды