ABB Ability MACHsense-R Скачать руководство пользователя страница 15

Страница: 15 / 74

See chapter/section

Task

Installing the accelerometers (page 35)

Install the accelerometers for vibration
measurement

Installing the Magnetic Field Sensor (page 43)

Install the magnetic field sensor

Installing the DAU (page 47)

Install the DAU

Connecting the cables (page 51)

Connect the cables

Connecting temperature sensors (page 59)

Optional: Connect the temperature sensor
(PT100 RTD/BTD)

Using RS485 interface (page 61)

Optional: Connect the RS485 interface

Using GPIO interface (page 63)

Optional: Connect the GPIO interface

Terms and abbreviations used in this manual.

Explanation

Term

Measures the vibration or acceleration of motion

Accelerometer

Access Point Name is a gateway between a mobile network and an-
other computer network.

APN

Data Acquisition Unit. It is used in a monitoring system to collect
data from different sensors.

DAU

General Packet Radio Service. It is a non-voice high-speed packet
switching system for GSM networks.

GPRS

Global System for Mobile. It is a network connection commonly used
in mobile phones.

GSM

Local area network. It connects devices and applications in close
proximity via Ethernet or Wi-Fi.

LAN

Remote condition-monitoring service for motors and generators.

MACHsense-R

Introduction 15

Содержание Ability MACHsense-R










































































Результаты поиска

Содержание Ability MACHsense-R

Отзывы:

Похожие инструкции для Ability MACHsense-R

Бренды по названию

Популярные бренды

ABB Ability MACHsense-R, Руководство пользователя

Результаты поиска

Содержание Ability MACHsense-R

Отзывы:

Похожие инструкции для Ability MACHsense-R

Бренды по названию

Популярные бренды