abaco systems SBC329 3U VPX Скачать руководство пользователя страница 67

Страница: 67 / 137

Publication No. SBC329-HRM/1

Functional Description 67

5.17.1

EEPROM DIP Switch

A PCA9560 device is used to configure the following aspects of board operation:

Table 5-17 DIP Switch Options

Internal Register
and Bit

Output
(Datasheet Name)

Function

REG0 bit 0

MUX_A

Boot SPI select:

0 = Boot from main SPI site
1 = Boot from FSP SPI site

REG0 bit 1

MUX_B

COM2 interface mode:

0 = COM2 transceiver is in RS232 mode (default)
1 = COM2 transceiver is in RS422 mode

REG0 bit 2

MUX_C

ZHURe NVRAM write protect:

0 = ZHURe NVRAM is write-enabled (default)
1 = ZHURe NVRAM is write protected

REG0 bit 3

MUX_D

NVRAM write protect
0 = Writes to NVRAM are enabled whenever the NVMRO signal is inactive (default)
1 = Writes to NVRAM are disabled

REG0 bit 4

MUX_E

SSD write protect

0 = Writes to SDD are enabled whenever the NVMRO signal is inactive (default)
1 = Writes to SDD are enabled

NOTE

Setting this bit to a ‘

’ may cause instability if an operating system

is installed on the SSD

REG0 bit 5

NON_MUXED_OUT Backplane PCIe REFCLK enable

0 = REFCLK is not driven (default)
1= REFCLK is driven at 100 MHz

REG1 bit 0

Not connected

Run BIT (reserved for use by FSP):

0 = Boot into the FSP menu
1 = Run BIT

REG1 bit 1

Not connected

BIT Verbose mode (reserved for use by FSP):

0 = BIT Verbose mode disabled
1 = BIT Verbose mode enabled

REG1 bit 2

Not connected

BIT Fast Start mode:

0 = BIT Fast Start disabled
1 = BIT Fast Start enabled

REG1 bit 3

Not connected

Fast BIT mode

0=Fast BIT mode disabled
1=Fast BIT mode enabled

REG1 bit 4

Not connected

Not used

REG1 bit 5

Not connected

Not used

NOTE

The EEPROM DIP Switch is write-enabled only when the backplane NVMRO signal (on

P0 pin

) is low (inactive) and the

Configuration EEPROM Write Protect Link (P6)

has a jumper fitted.

The EEPROM DIP switch can be controlled using the BIOS set-up screen.
It is intended only to be used by Abaco software drivers.

LINK

For more details on the DIP switch, see

http://www.nxp.com

Содержание SBC329 3U VPX










































































































































Результаты поиска

Содержание SBC329 3U VPX

Отзывы:

Бренды по названию

Популярные бренды

abaco systems SBC329 3U VPX, Справочник по аппаратуре

Результаты поиска

Содержание SBC329 3U VPX

Отзывы:

Бренды по названию

Популярные бренды