manualshive.com logo in svg

abaco systems SBC329 3U VPX, Справочник по аппаратуре

Поделиться
Скачать
abaco systems SBC329 3U VPX Скачать руководство пользователя страница 39

 

Publication No. SBC329-HRM/1 

  

Installation and Power Up/Reset  39 

XMC Speed 

This allows the speed (Gen1 @ 2.5 Gbits/second, Gen2 @ 5 Gbits/second or Gen3 @ 
8 Gbits/second) of the XMC link to be set. 

  NOTE 

Gen3 operation is not guaranteed, and its operation should be validated by the end user before 

use. 

Dataplane Configuration 

This configures the backplane Dataplane PCIe configuration. 
Allowable configurations are x8, x4+x4, x2+x2+x2+x2 

  NOTE 

If an operating system has configured the SBC329 for NT operation, it is not possible to alter 
the backplane configuration using this menu, and the option will be greyed-out. In this 
configuration, only the operating system can change this setting. 

DPx Speed 

This allows the speed (Gen1 @ 2.5 Gbits/second, Gen2 @ 5 Gbits/second or Gen2 @ 
5 Gbits/second) of each Expansion Plane link to be set. This is useful when it is 
desirable to force the SBC329 to operate at a lower link speed. For instance, when 
cables are being used in a development backplane to connect the Expansion Plane, 
forcing Gen1 mode using this method is recommended. 

  NOTE 

Gen3 operation is not guaranteed, and its operation should be validated by the end user before 

use. 

Program EEPROM 

Once the required PCIe switch settings have been made, select this option to 
program the configuration into the EEPROM. The new configuration is only 
activated 

after

 the board has been reset or power cycled. 

  NOTE 

Ensure that the EEPROM is write-enabled before selecting this option, i.e. a jumper is fitted on 
the 

Configuration EEPROM Write Enable Link (P6)

, and the backplane NVMRO signal is inactive. 

Lock EEPROM 

This locks the EEPROM. When locked, the EEPROM 

cannot

 be overwritten by third 

party software (such as PLX development tools), regardless of the state of the write 
protect links and NVMRO. 

By default, the EEPROM is unlocked. 

Unlock EEPROM 

This unlocks previously locked EEPROM. The EEPROM is unlocked by default. 

  NOTE 

Once locked, the EEPROM can only be unlocked when it is write-enabled, i.e. a jumper is fitted 
on the Configuration EEPROM Write Enable Link (P6), and the backplane NVMRO signal is 
inactive. 

Содержание SBC329 3U VPX










































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды