manualshive.com logo in svg

abaco systems SBC329 3U VPX, Справочник по аппаратуре

Поделиться
Скачать
abaco systems SBC329 3U VPX Скачать руководство пользователя страница 57

 

Publication No. SBC329-HRM/1 

  

Functional Description  57 

5.7.2  

 

Dual BASE-T Variant (SBC329-xxx2xxxxx) 

In this configuration, ETH0 and ETH1 are configured as 10/100/1000BASE-T. 
ETH2 is not available in this configuration. The channels are connected to the VPX 
P1 connector as follows: 

Table 5-5 ETH0/ETH1 Pin Mapping - Dual BASE-T Variant 

Signal 

P1 Pin  Signal 

P1 Pin 

ETH0_0P 

A13 

ETH1_0P 

A15 

ETH0_0N 

B13 

ETH1_0N 

B15 

ETH0_1P 

D13 

ETH1_1P 

D15 

ETH0_1N 

E13 

ETH1_1N 

E15 

ETH0_2P 

B14 

ETH1_2P 

B16 

ETH0_2N 

C14 

ETH1_2N 

C16 

ETH0_3P 

E14 

ETH1_3P 

E16 

ETH0_3N 

F14 

ETH1_3N 

F16 

5.8  GPIO 

The SBC329 provides up to four lines of General Purpose I/O, each with interrupt 
generation capabilities. Availability of the GPIO signals depends on the build 
variant. The table below summarizes the availability and signal routing: 

Table 5-6 GPIO Line Signal Availability 

GPIO Line  Build Variant Availability  Pin 

Alternate Function 

0 

SBC329-xxxx3xxxx 

P2/G3  COM2_TXD/TXD_A 

1 

SBC329-xxxx3xxxx 

P2/G5  COM2_RXD/RXD_A 

2 

SBC329-xxxx1xxxx & 
SBC329-xxxx3xxxx 

P2/G7  COM2_RTS~/TXD_B/AXIS_CLK 

3 

SBC329-xxxx1xxxx & 
SBC329-xxxx3xxxx 

P2/G9  COM2_CTS~/RXD_B/AXIS_RST 

These are 3.3 V single-ended signals with 5 V tolerance. These signals are controlled 
by the FPGA and can be configured as inputs, with the ability to generate level- or 
edge-triggered interrupts. 

The GPIO signals are intended only to be used by Abaco software drivers. See the 
relevant software manual for details. 

GPIO(2) and GPIO(3) are shared with the AXIS_CLK and AXIS_RST signals 
respectively. If AXIS operation is required, these signals cannot be used as GPIO. 
See

 section 5.22.2

 for more information. 

 

 

Содержание SBC329 3U VPX










































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды