background image

GX-A/GF-A Maintenance manual 

 

Page 11 

4. Corrective Maintenance 

Perform  corrective  maintenance  for  the  GX-A/GF-A  series  by  referring  to  the  maintenance 
flowchart  and  the  troubleshooting  table.  The  troubleshooting  table  describes  the  possible 
cause and solution to facilitate corrective maintenance.   
 
Perform  corrective  maintenance  according  to  the  error  (the  letters  refer  to  nodes  on  the 
maintenance flow chart): 

Type A:  Replacing, disassembling, or assembling the force motor unit 
Type B:  Replacing or adjusting electrical parts 
Type C:  Initializing the electric board and inputting specific data 
Type D:  Adjusting the characteristics of the force motor unit 
Type E:  Inputting temperature data 
Type F:  Performance test   
Type G:  Performing drift check 
Type H:  Replacing the main board 

 

  4.1    Troubleshooting Table 

The  following  troubleshooting  table  describes  the  possible  cause  of,  and  the  solution  to 
problems.   

Problem 

Cause 

Check 

Solution 

Type 

No 

display, 

beam  is 

not 

balanced 

 

AC adapter 

Is  it  the  correct  AC  adapter  for  the 

power source used? 

Replace  with  the  correct  AC 

adapter. 

Is  the  output  voltage  correct?  Measure 

the  output  voltage  of  the  AC  adapter 

when  it  is  connected  to  the  balance. 

The  DC  output  should  be  at  least  11 

volts, but no greater than 22 volts. 

If the output voltage is not correct, 

replace the AC adapter. 

 

 

 
 
 

Power  supplies  of 

main board 

and 

display 

board 

Is  the  output  of  each  power  supply 

correct? (Refer to Table-1 of page 15)   

Check the Vdd, Vgc, Vcc, VLDC. 

Check (replace) the main board or 

display 

board 

with 

substitute 

items. 

Check  (replace)  the  defective 

power supply part with a substitute 

item. 

 

Force motor 

Check  that  the  connectors  are  installed 

correctly(J10A).   

Replace  the  force  motor  with  a 

substitute item. 

(Refer 

to 

“5.  Force  Motor 

Disassembly and Reassembly

”) 

Main 

board 

assembly 

 

Check  the  performance  using  the 

standard 

main 

board 

that 

works 

properly. 

Replace the main board assembly 

with a substitute item. 

 

Analog 

board 

assembly 

Check  the  performance  using  the 

standard  analog  board  that  works 

properly. 

Replace 

the 

analog 

board 

assembly with a substitute item. 

 
 
 

Содержание GF-A Series





















































Отзывы: