A&D GF-A Series Скачать руководство пользователя

Страница: 34 / 52

GX-A/GF-A Maintenance manual

Page 32

6.6 Model type Selection (Only for maintenance electric board)

Model type selection is available for the maintenance board only.

Model selection procedure

Follow the procedure below to select the balance model type.

Step 1. Verify the following item of the 7PZ-6594B/C (Main board

for the maintenance

□

Verify the type of the board

・

For each type (B/C), verify that the jumper setting is correct. (Refer to the

Technical information

“3. Circuit Diagram” and “4. Part Layout”)

□

For the main board unit, verify if it is adjusted completely

・

Connect the AC adapter to the main board unit. If

error 9

is displayed, the

main board is not adjusted yet and it should be adjusted for a maintenance
board.

Step 2. See the check mode menu flowchart on page 29 to display basic setting mode

typeE

Step 3. Press the PRINT key. Confirm the type on the display as follows.

Type of board

Model type which can be set

Type displayed initially

7PZ-6594B

GX-203A/303A/403A/603A/1003A/1603A

GF-123A/203A/303A/403A/603A/1003A/1603A

GX-1603A

7PZ-6594C

GX-2002A/3002A/4002A/6002A/10002A

-6001A/10001A

GF-1202A/2002A/3002A/4002A/6002A/10002A

-6001A/10001A

GX-10002A

Use the following keys to select the model type

RE-ZERO key: changes the model type. (Change the model type according to

the kinds of PZ)

PRINT key:

saves the final model type.

CAL key:

cancels the data.

When the model after change is the same as that before change, the stabilization
indicator illuminates.

Step 4. Press the PRINT key.

end

appears. Then, the next item appears.

Содержание GF-A Series





















































Результаты поиска

Содержание GF-A Series

Отзывы:

Похожие инструкции для GF-A Series

Бренды по названию

Популярные бренды

A&D GF-A Series, Руководство по обслуживанию

Результаты поиска

Содержание GF-A Series

Отзывы:

Похожие инструкции для GF-A Series

Бренды по названию

Популярные бренды