A.O. Smith Innovo IR 12-160 Скачать руководство пользователя страница 79

Страница: 79 / 96

Code and description

Cause

Measure

F11

(blocking error)

Ionisation error

Ionisation measured with
a closed gas control valve

Defective gas control valve.

Make sure that there is no flame after
the gas control valve has closed.

If there is a flame, the gas control
valve must be replaced.

F19

(blocking error)

Supply voltage error

Three unsuccessful
ignition attempts.

There is not enough or too much supply
voltage during 60 seconds.
The measured voltage between live and
neutral must be 230 V

(-15%,

+10%).
The supply voltage between live and
earth must be between 110 V

and

230 V

(-15%, +10%)

Make sure that the supply voltage on
the controller is correct.

If the supply voltage is above or below
the stated tolerance and the error
persists, contact your maintenance
and service engineer.

Install an isolating transformer.

F21

(lock out error)

Air proving switch error

Switch is not closed, while
fan runs during post purge

Damaged wiring/open circuit.

See measure of error

F03

- Switch is not

closed when fan is running during pre-
purge.

S02

(blocking error)

Sensor error

Open circuit from sensor 1
of the temperature sensor

Sensor is not (correctly) connected.

Make sure that the connector is
connected to J3.

Make sure that the wire is connected
to the sensor.

Damaged wiring and/or defective sensor. Replace the wiring and/or sensor.

S03

(blocking error)

Sensor error

Open circuit from sensor 2
of the temperature sensor

Sensor is not (correctly) connected.

Make sure that the connector is
connected to J3.

Make sure that the wire is connected
to the sensor.

Damaged wiring and/or defective sensor. Replace the wiring and/or sensor.

S12

(blocking error)

Sensor error

Short circuit in sensor 1 of
the temperature sensor

Short circuit in the sensor circuit.

Replace the wiring and/or sensor.

S13

(blocking error)

Sensor error

Short circuit in sensor 2 of
the temperature sensor

Short circuit in the sensor circuit.

Replace the wiring and/or sensor.

0312266_INNOVO_UKUK_

V5.1, 2022-07-12

Содержание Innovo IR 12-160

































































































Результаты поиска

Содержание Innovo IR 12-160

Отзывы:

Похожие инструкции для Innovo IR 12-160

Бренды по названию

Популярные бренды

A.O. Smith Innovo IR 12-160, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Innovo IR 12-160

Отзывы:

Похожие инструкции для Innovo IR 12-160

Бренды по названию

Популярные бренды