A.O. Smith Innovo IR 12-160 Скачать руководство пользователя страница 42

Страница: 42 / 96

Installation
type

Version

Description

C43

Closed

Water heaters on common air inlet and flue gas
outlet (concentric and/or parallel) in a multiple
floor building.

C53

Closed

Separate air inlet and flue gas outlet terminal
types mixed. Air inlet and flue gas outlet
termination may be in different pressure zone.

C63

Closed

Water heaters supplied without venting materials.
These water heaters must be installed in
compliance with local regulations. The water heater
is intended to be connected to a separately
approved and marketed venting system.

This manual does not discus installation type B23. When you need a B23 system, contact
A.O. Smith for more information.

Caution
Always make sure that the venting system is mounted into an area suitable for the
correct type of installation.

Installation, Maintenance and Service part

Содержание Innovo IR 12-160

































































































Результаты поиска

Содержание Innovo IR 12-160

Отзывы:

Похожие инструкции для Innovo IR 12-160

Бренды по названию

Популярные бренды

A.O. Smith Innovo IR 12-160, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Innovo IR 12-160

Отзывы:

Похожие инструкции для Innovo IR 12-160

Бренды по названию

Популярные бренды