manualshive.com logo in svg

3M GMI PS200-LMP, Руководство по эксплуатации и техническому обслуживанию, Страница: 9 / 46

Поделиться
Скачать
3M GMI PS200-LMP Скачать руководство пользователя страница 9

64220, Rev. 1/April 2019

3M™ GMI™ PS200-LMP AUTO BUMP/CALIBRATION STATION

ABOUT THIS GUIDE

1-1

1. ABOUT THIS GUIDE

This guide instructs gas detection personnel on the features and usage of the PS200-LMP Auto 

Bump/Calibration Station (or “the ABC”), including information on configuration, operation, mainte-

nance, specifications, and troubleshooting.
This user guide assumes the reader has a basic knowledge of gas detection procedures. 
The user guide is divided into the following topics:

•

2. INTRODUCTION

•

3. CONNECTIONS

 

•

4. WARM-UP SEQUENCE

•

5. PERFORMING A CALIBRATION/BUMP TEST

•

6. CREATE/VIEW CERTIFICATES

•

7. RE-CONFIGURING THE ABC

•

APPENDIX A. SPECIFICATIONS

•

APPENDIX B. USB MEMORY STICK CONTENTS

•

APPENDIX C. FIT MOUNTING BRACKET

•

APPENDIX D. TECHNICAL SUPPORT

1.1. Guide Conventions

The following visual elements are used throughout this guide, where applicable: 

WARNING: THIS ICON AND TEXT INDICATE A POTENTIALLY HAZARDOUS 

SITUATION, WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR 

INJURY.

CAUTION: This icon and text indicate an action or situation, which, if not avoided, could 

result in damage to the equipment.

NOTE: This icon and text designates information of special note.

WARNING: READ, UNDERSTAND AND FOLLOW THE ENTIRE CONTENT OF THIS 

GUIDE PRIOR TO USE. FAILURE TO DO SO MAY RESULT IN SERIOUS 

INJURY OR DEATH.

Содержание GMI PS200-LMP















































Отзывы:

Нет отзывов