manualshive.com logo in svg

3M GMI PS200-LMP, Руководство по эксплуатации и техническому обслуживанию, Страница: 3 / 46

Поделиться
Скачать
3M GMI PS200-LMP Скачать руководство пользователя страница 3

64220, Rev. 1/April 2019

3M™ GMI™ PS200-LMP AUTO BUMP/CALIBRATION STATION

LICENSE AGREEMENT

iii

LICENSE AGREEMENT

This License Agreement is your proof of license.

Important - Read Carefully

This is a legal and binding contract between you (either an individual or an entity), the end user and 

Gas Measurement Instruments Limited (GMI). By installing, copying, or otherwise using the ‘PS200 

Settings’ Auto Bump / Cal Station application program (“SOFTWARE”), you agree to be bound by 

the terms of this agreement. If you do not agree to the terms of this agreement you should return this 

item, including documentation, to GMI.

Calibration Software License

1. GRANT OF LICENCE: The ‘PS200 Settings’ License Agreement (License) permits concurrent 

use of the SOFTWARE on the number of computers for which this license grants (that is: single 

user package licenses one user; twenty user package licenses twenty users). Additional SOFT-

WARE licenses may be purchased for each additional concurrent user.
If you have acquired this SOFTWARE in a multiple license pack, you may make the number of 

additional copies of the SOFTWARE authorized on the printed copy of the license. You may also 

store or install a copy of the network SOFTWARE on a storage device, such as a network server, 

used only to install or run the SOFTWARE on your other computers over an internal network; 

however you must acquire and dedicate a license for each separate computer on which the 

SOFTWARE is installed or run from the storage device. A license for the software may not be 

shared or used concurrently on different computers. 
This license is granted for use on the GMI products and for use on one computer. If you require a 

second copy you must purchase that from GMI or its distributor. The documentation accompa-

nying this software is essential for the correct and safe operation of the instruments.
This software is used on certified equipment which may be used in life critical applications. Only 

trained competent personnel should use this equipment and should be aware of the certification, 

calibration and Health and Safety issues associated with the product and its application.

2. COPYRIGHT: The SOFTWARE is owned by GMI and is protected by United Kingdom copyright 

laws and international treaty provisions. Therefore you must treat the SOFTWARE like any other 

copyrighted material (for example, a book or musical recording) except that you may either (a) 

make one copy of the SOFTWARE solely for backup or archival purposes, or (b) transfer the 

SOFTWARE to a single hard disk provided you keep the original solely for backup and archival 

purposes. You may not copy the written materials accompanying the SOFTWARE.

3. OTHER RESTRICTIONS: You may not rent or lease the SOFTWARE, but you may transfer the 

SOFTWARE and accompanying written materials on a permanent basis to another individual. If 

you transfer the software, you must retain no copies and the recipient must agree to the terms of 

this agreement. You must not reverse engineer, decompile, or disassemble the SOFTWARE that 

is provided solely as executable programs (.EXE files) or dynamic link libraries (.DLL files). If the 

SOFTWARE is an update, any transfer must include the update and all prior versions.

Содержание GMI PS200-LMP















































Отзывы:

Нет отзывов