3M Bair paws 875 Скачать руководство пользователя страница 26

Страница: 26 / 33

Bair Paws Model 875 Warming Unit Service Manual

Check the 3M

Bair Paws

system website to ensure you have the most recent version of this document.

www.bairpaws.com reorder #202036A

Replacing the Power Cord

Tools/Equipment Needed

•

Medium Phillips screwdriver�

Method

1� Disconnect the warming unit from the power source�

2� Loosen the two screws that secure the cord

retainer to the warming unit� The screws should

be backed out by 1/8" to allow the removal of the

cord retainer (Figure 17)�

Note: Do not back the cord retainer screws out

completely�

3� Rotate the cord retainer to free it from the screw

heads and slide it off of the cord (Figure 18)�

4� Pull the plug of the old cord out of the unit�

Dispose of the old cord�

5� Insert the plug of the new cord into the unit�

6� Position the cord retainer onto the new cord�

7� Secure the cord retainer to the warming unit

with the two screws�

8� Reconnect the warming unit to the power

source and turn the temperature controller

on to make sure the warming unit functions

properly before returning to service�

Figure 17�

View of a fully

installed cord

retainer�

Figure 18�

Uninstalling

the cord retainer�

Содержание Bair paws 875


































Результаты поиска

Содержание Bair paws 875

Отзывы:

Похожие инструкции для Bair paws 875

Бренды по названию

Популярные бренды

3M Bair paws 875, Руководство по обслуживанию

Результаты поиска

Содержание Bair paws 875

Отзывы:

Похожие инструкции для Bair paws 875

Бренды по названию

Популярные бренды