3D Systems ProX 950 Скачать руководство пользователя страница 54

Страница: 54 / 62

3D Systems, Inc.

CUSTOMER SUPPORT

If you receive an unrecoverable error message, or if you need to contact us for another problem, you may contact our Customer

Support Hotline. Before you call Customer Support with a problem or question, please make sure that you have the following

information:

•

The serial number of your ProX 950 (located on the rear panel)

•

A brief description of the problem, including the exact error message

•

When the problem occurred; for example, when you submitted a job, during the beginning or the end of a print, or

after power off recovery

CUSTOMER SUPPORT HOTLINE

Please contact your Customer Support Hotline at one of the following numbers:

•

US and Canada: 888-598-1438

•

UK and EMEA: +44 1442 279883

•

International: +1 803-326-3930

ORDER INQUIRIES

For all order inquiries, please send an email to one of the following addresses:

•

Americas and Asian Pacific: [email protected]

•

Europe/Middle East/Africa: [email protected]

SERVICE

GENERAL

ProX 950 service procedures must be performed only by a 3D Systems-certified service technician unless this guide explicitly

states otherwise. If your system needs service, contact 3D Systems Technical Support at the following numbers:

•

In the United States or Canada, call 800-793-3669

•

In Europe, call +49-6151-357357

You can also contact your local 3D Systems representative.

3D Systems’ support portal is located at

http://www.3dsystems.com/support

For material safety data sheet, go to

http://www.3dsystems.com/support/materials/msds

LASER

UV Radiation

All Laser service procedures may only be performed by 3D Systems certified service technicians. Attempts by

non-certified personnel to perform Laser service procedures can result in serious injury. All ProX 950 users must

observe the guidelines and warnings located in the section

Laser Safety on page 9

The ProX 950 conforms to applicable requirements of 21 CFR Subchapter J at the date of manufacture. It is designated a Class

I Laser Device by the Center for Devices and Radiological Health (CDRH). In normal operation, the Laser beams are completely

confined and the viewing windows in the Process Module block the UV Laser radiation. However, if the Laser cover, doors, or

windows, are removed for any reason, the unit becomes a dangerous Class IV Laser device. Direct or reflected Laser power

from a Class IV Laser device can cause eye damage. See

Laser Safety on page 9

for more information.

Содержание ProX 950






























































Результаты поиска

Содержание ProX 950

Отзывы:

3D Systems ProX 950, Руководство пользователя, Страница: 54 / 62

Результаты поиска

Содержание ProX 950

Отзывы: