manualshive.com logo in svg

3D Systems ProX 950, Руководство пользователя, Страница: 48 / 62

Поделиться
Скачать
3D Systems ProX 950 Скачать руководство пользователя страница 48

3D Systems, Inc.

MATERIAL CONTAINER REMOVAL

When a material container is empty and needs to be refilled, or if a partially filled container needs to be replaced with a full 

container, perform the following procedure. 

It is important to verify the type of material currently in the MDM before proceeding with these steps . 

IRRITANT! Wear protective clothing, disposable nitrile gloves, and goggles, while performing the following 

steps:

1.  Open the front door of the system for the correct print 

zone.

2.  Place the vent cap on the vent hole and screw tightly 

to prevent the material from dripping on the currently 

installed bottle. The vent cap is the cap that was removed 

when material was originally placed in the material bin.

Release Lever

3.  Pull down on the MDM release lever which is  located to 

the left of the material bin, away from the MDM at a 45

° 

angle.

Release Lever

Container Release Button

Container Release Button

4.  Push the container release button, located on the lower 

right corner of the material bin.

5.  Lift the handle to remove the container. Dispose of the 

container according to local regulations.

6.  Using a disposable paper towel, wipe all material from the 

container seal assembly. If you notice any material on the 

container seal assemblly use a paper towel with a small 

amount of isoporopyl alcohol on it to clean it up.

A

B

48

Содержание ProX 950































































Отзывы:

Нет отзывов