3D Systems ProX 950 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 62

3D Systems ProX 950 Скачать руководство пользователя страница 49

3D Systems, Inc.

Vent Cap

REPLACING MATERIAL CONTAINERS

IRRITANT! Wear protective clothing, disposable nitrile gloves, and goggles, while performing the following

steps:

Note: Before adding a new container, make sure that the container slot is empty . If a container is present, refer

to the previous section,

Material Container Removal on page 48

before continuing .

To place a material bottle into the MDM, perform the following steps:
1. Open the print chamber doors.
2. Obtain a material bottle ensuring that it is the same material as currently

installed in the MDM.

3.

Pull the refill container’s release lever away from the MDM.

Release Lever

Container Release

Button

4. Insert the material bottle into the slot.
5. Look at the status on the user interface. If the status is okay, push the bottle

until you hear a click. Try to lift up on the bottle, if it does not release it is

properly seated..

6. Remove the vent cap and if the bottle is new puncture a small hole on the

bottle using something with a sharp point such as, a screw driver tip or a drill

bit tip.

Note: All bottles have a depression in the area to be punctured .

Unless the vent has been previously punctured, and you are very

certain of this, puncture the vent .

7.

Close the refill container door firmly until it latches securely.

8. Close the chamber doors, until they latch securely.

49

«
...
47
48
49
50
51
...
»

Содержание ProX 950































































Отзывы:

Нет отзывов